Arch sizes and block counts
Block counts for a 1-block-thick arch. Pick a size to open it in the generator.
| Size | Type | Opening | Blocks | Good for |
|---|---|---|---|---|
| 5 × 4 | Round | 3 × 3 | 9 | Doorways |
| 7 × 5 | Round | 5 × 4 | 11 | Wide doors and gates |
| 9 × 7 | Round | 7 × 6 | 17 | Archways and halls |
| 7 × 7 | Pointed | 5 × 6 | 13 | Gothic windows |
| 9 × 9 | Pointed | 7 × 8 | 17 | Church doors |
| 15 × 8 | Round | 13 × 7 | 21 | Castle gates and tunnels |
| 21 × 11 | Round | 19 × 10 | 29 | Big bridges and aqueducts |
| 21 × 6 | Shallow | 19 × 5 | 21 | Stream bridges |
| 31 × 8 | Shallow | 29 × 7 | 31 | River bridges |
Minecraft arch chart: common sizes
Round, pointed and shallow arches
- Round: A semicircle. Make the height half the width, rounded up, for a perfect half circle (9 × 5, 15 × 8). Make it taller and the sides run straight down like a Roman doorway; lower and it flattens into a half-ellipse.
- Pointed: Two curves that meet in a point at the top, also called a gothic arch. Make the height more than half the width; about as tall as it is wide gives the classic church door or castle window.
- Shallow: A slice of a large circle, lower than a semicircle, also called a segmental arch. Make the height less than half the width. It spans a long gap without getting tall, which is why most stone bridges use it.
How to make an arch in Minecraft
An arch is built like the top half of a circle standing on its side. Build it from the ground up, one row at a time, and both halves stay even.
- Measure the gapWidth is the whole arch, sides included; height runs from the ground to the top block. For a doorway, add 2 to the opening width you want and 1 to its height.
- Lay row 1 and the sidesPlace row 1 of the build list on the ground, then stack the two sides. Rows count up from the ground, the same as on the blueprint.
- Follow the curve upEach row moves in as the arch closes. Copy the columns for each row; the blue line marks the middle, so check both halves against it.
- Close it at the topFinish with the top row: one keystone for an odd width, two blocks for an even one. For a thicker wall, repeat the same arch behind the first.
Archways and arched doorways
An archway is an arch you can walk through. It reads best when the frame stands out from the wall, so use a different block or set the wall thickness to 2.
- Doors: a 5 × 4 round arch leaves a 3 × 3 opening, room for a door with a block of trim on each side. A 4 × 4 arch leaves 2 × 3, a snug fit for a double door.
- Gates and halls: 9 × 7 and 15 × 8 suit castle gates, mine entrances and corridors. Repeat the arch every 3 or 4 blocks along a hallway for a vaulted ceiling.
- Windows: pointed arches such as 5 × 6 or 7 × 7 make gothic windows. Fill the opening with glass panes.
- Cutting an arch into a wall: pick Filled to get the whole arch shape, then remove exactly those blocks from the wall.
How to build an arch bridge in Minecraft
For an arched bridge, set the width to the gap you want to cross and pick a shallow arch: 21 × 6 over a stream, 31 × 8 over a river. Round arches suit tall bridges and aqueducts with several arches in a row.
- Build the arch on one edge of the bridge, then the same arch on the other edge, 3 to 5 blocks apart for a path.
- Join the two arches block by block along the curve, or fill the whole space between them for a solid bridge.
- Lay the deck on top and add a railing of walls or fences.
- For a long bridge, set several arches side by side with a pillar between each pair.
The .litematic file loads the arch standing upright in Litematica, ready to copy along the bridge.
Smoother arches with stairs and slabs
- Fill the steps with stairsWhere the curve steps up by one block, put an upside-down stair in the corner under the step. It hides the jagged edge and is the usual way to make an arch with stairs.
- Use slabs where it flattensNear the top the curve is almost level. A top slab in each gap halves the step and rounds it off.
- Go thicker on big archesA 1-block outline looks thin on anything wider than about 15 blocks. Set the wall to 2 or 3 and use a contrasting block for the inner ring.
- Keep both halves equalCount each row from the build list instead of by eye. One misplaced block near the top makes the whole arch look lopsided.
Building a round tower or a domed hall around the arch? Use the circle generator for the floor plan and the dome generator for the roof.
FAQ
How do you make an arch in Minecraft?
Set the width and height in the generator and pick an arch type. Build row 1 on the ground and work up, copying the columns for each row from the build list. A round arch is the top half of a circle drawn block by block.
How big should a Minecraft arch be?
For a doorway, 5 × 4 (a 3 × 3 opening) or 7 × 5. For gates and halls, 9 × 7 to 15 × 8. For a perfect semicircle, make the height half the width, rounded up: 9 × 5, 15 × 8, 21 × 11.
How do you make a 5-wide arch?
Set the width to 5. A height of 3 gives a half circle and 4 adds a straight block on each side; both leave a 3-wide opening. Pick Pointed and a height of 5 or 6 for a narrow gothic window.
How do I make an arch with stairs and slabs?
Build the block arch from the blueprint first. Then put upside-down stairs under each one-block step and top slabs where the curve is almost flat. The blocks are the frame; the stairs and slabs smooth it.
How do I make a gothic arch?
Pick Pointed and make the height more than half the width. An arch about as tall as it is wide, such as 9 × 9, gives the classic gothic shape.
What arch is best for a bridge?
A shallow arch spans a wide gap without getting tall. Set the width to the gap and the height to about a quarter of it, such as 21 × 6 or 31 × 8.
Is there a WorldEdit command for an arch?
No. WorldEdit has no arch command, and its cylinder commands lie flat on the ground. Download the .litematic file instead: it loads standing up in Litematica.
Does it work on Bedrock?
Yes. The blueprint is the same on Java and Bedrock. The .litematic file needs the Litematica mod, which runs on Java.