Free · 2x2, 3x3, 5x5 and round towers · layer by layer

Minecraft Spiral Staircase Generator

Pick a square or round stairwell, the step width and the height, and get the staircase layer by layer: one new step per layer, with the pillar and the tower wall if you want them. Turn it in 3D, then save a PNG or a .litematic file.

Tap a block to mark it placedRow and column numbers match the build listCenter linesLayer belowThicker grid every 5 blocks

Row-by-row build list

RowBlocksColumns

Side view

slice through the center
Tap a row to jump to that layer.

Spiral staircase sizes

Stairwell is the space inside the walls. A full turn climbs one block per step, so steps per turn is also the height of one turn; headroom is the air above each step. Blocks per turn counts the steps and the pillar. Pick a size to open it in the generator.

StairwellStep widthSteps per turnHeadroomBlocks per turnGood for
2x21434Tight bases and mineshafts
3x318716Towers and houses
4x41121160Small towers
5x528732Compact 2-wide stairs
5x511615160Towers with a thick core
7x721615184Castles and keeps
9x9 round22423368Round towers
11x11 round31615172Wizard towers and lighthouses

Spiral staircase designs from above

The number on each block is the step it belongs to: build step 1 on the first layer, step 2 one layer higher, and so on. The orange blocks are the pillar.

How to make a spiral staircase in Minecraft

A spiral staircase climbs one block for every step and turns around a pillar or an open middle. The generator works out which blocks make each step, so you only follow it layer by layer.

  1. Pick the stairwell and the step widthThe stairwell is the space inside the tower walls. 3x3 is the classic small spiral, 5x5 with 2-wide steps is comfortable, and round stairwells fit round towers.
  2. Build the first stepLayer 1 holds step 1, at the bottom of the board next to the center line, and the pillar if you keep it.
  3. Go up one layer per stepMove the layer slider up. Each layer has one new step right next to the last one, shown in grey. Keep stacking the pillar as you go.
  4. Use stairs for the stepsWith full blocks you have to jump every step. Put a stair block on each step, facing the way you climb, and you can walk all the way up.
  5. Add the wallTurn on Outer wall for a tower around the stairs, or build the stairs inside a tower you already have: set the stairwell to its inside width.

Square or round, pillar or open

Square stairwells (2x2 to 9x9) fit square towers, houses and mineshafts, and every step lines up with the walls. Round stairwells go inside round towers: an 11-wide round stairwell with the wall on is 13 blocks across. Build the rest of the tower with the circle generator and cap it with the dome generator.

Pillar or open. The pillar is everything inside the steps. On a 3x3 it is a single block; on bigger stairwells it is a thick core, so pick Open for a hollow middle you can drop through or hang a chandelier in.

Step width. 1-wide steps take the fewest blocks. 2- or 3-wide steps are easier to walk, but on the same stairwell they leave a smaller pillar, so a turn has fewer, broader steps and less headroom.

Steps per turn and headroom

Every step is one block above the last, so a staircase with 8 steps per turn climbs 8 blocks in one full turn. The step directly above yours is one turn higher, which leaves steps per turn minus one blocks of air over your head. Players need 2 blocks, so even a 2x2 spiral (4 steps, 3 blocks of headroom) is walkable.

Set the height to the floor you want to reach. Each layer adds exactly one step, so a 24-block climb needs a height of 24, and the readout shows how many turns that is.

FAQ

How do you make a spiral staircase in Minecraft?

Pick the stairwell size and step width in the generator. Build step 1 on the first layer, then go up one layer at a time and place the next step next to the last one. Use stair blocks on the steps so you can walk up without jumping.

What is the smallest spiral staircase?

A 2x2: four steps per turn around the middle, with 3 blocks of headroom. It has no pillar. A 3x3 is the smallest with a pillar: one block in the middle and 8 steps around it.

How do you make a 3x3 spiral staircase?

Put a 1-block pillar in the middle and the 8 blocks around it are the steps, one per layer. A full turn climbs 8 blocks and leaves 7 blocks of headroom. Open the 3x3 preset to see each layer.

How many steps are in one turn?

One for each block next to the pillar: 4 on a 2x2, 8 on a 3x3, 16 on a 5x5 with 1-wide steps, and 8 on a 5x5 with 2-wide steps. Wider steps on the same stairwell make fewer steps per turn.

How do I make a spiral staircase inside a round tower?

Set the shape to Round and the stairwell to the inside width of the tower, then build the steps against the wall. Or turn on Outer wall and build the tower and the stairs together.

Should I use stairs or full blocks for the steps?

Stairs. Each step is one block higher than the last, so on full blocks you have to jump every step. Build the blueprint with stair blocks facing the way you climb, or place the full blocks first and swap them for stairs.

Can it turn the other way?

Yes. Switch Climbs to Counterclockwise. The board is a view from above, so the steps run the other way around the pillar.

Does it work on Bedrock?

Yes. The blueprint is the same on Java and Bedrock. The .litematic file needs the Litematica mod, which runs on Java.